Altronix AL802ULADA Installation Instructions Bedienungsanleitung PDF herunterladen (Seite 3)

AL802ULADA - 3 -

Power Supply Specifications:

AC Input:

120VAC60Hz,5amp,suppliedbyamaximum15ampdedicatedbranchcircuit.

Output:

Four(4)regulatedsupervisedNACoutputcircuits,24VDC,2.5ampmaximumcurrent.

One(1)aux.specialapplication24VDCpoweroutputcircuit1amp,non-supervised

totaloutputcurrentmustnotexceedcurrent8ampinAlarmCondition.

Battery:

Usetwo(2)12VDC/12AHortwo(2)12VDC/7AHbatteriesconnectedinseries.

Stand-by/Alarm Current

Consumption:

90mA/175mA

EOL Resistor

(end of line):

2.2K(2200ohm),AltronixModel#AL-EOL22(included).

Ground fault maximum

test impedance:

1000ohm.

Stand-by Specifications:

Stand-by Batteries Stand-by Time Total Amp/Minutes Alarm Output Current Aux. Output

24VDC/7AH 24Hours 8amp/5minutes ---

24VDC/12AH

(usetwo(2)12VDCbatteriesinseries)

24Hours 8amp/5minutes 50mA

24VDC/36AH 24Hours 8amp/5minutes 1amp

Note: Unit is equipped with 1 amp max. auxiliary output: “AUX” will remain battery backed up during power

outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” above for ratings. When

loads are connected to “AUX” output during alarm condition, the remaining outputs may, not exceed 8 amp total

alarm current (example: AUX = 1 amp, outputs up to 7 amp).

Installation Instructions:

WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/NFPA72/ANSI,andwithalllocal

codesandauthoritieshavingjurisdiction.

Productisintendedforindooruseonly.

 Carefully review:

Application Guide for AL602ULADA, AL802ULADA, AL1002ULADA

Power Supply Specifications (pg. 3)

Stand-by Specifications (pg. 3)

Output Programming Selection Table (pg. 4)

Sync Mode Selection Table (pg. 4)

Terminal Identification Table (pgs. 5-6)

LED Status Indication Table (pg. 6)

1.Mountunitinthedesiredlocation.Markandpredrillholesinthewalltolineupwiththetoptwokeyholesinthe

 enclosure.Installtwoupperfastenersandscrewsinthewallwiththescrewheadsprotruding.Placetheenclosure’s

 upperkeyholesoverthetwoupperscrews;levelandsecure.Markthepositionofthelowertwoholes.Removethe

 enclosure.Drillthelowerholesandinstalltwofasteners.Placetheenclosure’supperkeyholesoverthetwoupper

 screws.Installthetwolowerscrewsandmakesuretotightenallscrews(Enclosure Dimensions, pg. 12).

 Secureenclosuretoearthground(Fig. 1, pg. 3).

2.Connecttheline(L)andneutral(N)terminalstoaseparateunswitchedACcircuit(120VAC,60Hz)

 dedicatedtotheFireAlarmSystem.

3.Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.

4. Connectbatterytotheterminalsmarked[+BAT--]onthePowerSupplyBoard(batteryleadsincluded).

 Usetwo(2)12VDCbatteriesconnectedinseries.

5. Setoutputselectionswitchesmarked[OUT1throughOUT4]tofollowcorrespondinginput[IN1&IN2]and

 desiredoutputsignaltype (Output Programming Selection Table, pg. 4).

6. ConnectFACPoutputtothedesiredAL800LGK9Elogicboardinputs,andnotificationappliancestothedesired

 AL800LGK9Elogicboardoutputs(see Application Guide).

Note:The2-wirehorn/strobesyncmodewillonlysynchronizehorns,horn/strobes,strobeswith

 synchronizationcapability.

7. Forconnectionofsmokedetectors,digitaldialerseeOptional Hookup Diagram, pg. 7.

Fig. 1

L N

line

ground

neutral

1 2 3 4 5 6 7 8 ... 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Altronix AL802ULADA Installation Instructions Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör für elektrische Altronix AL802ULADA Installation Instructions